You mean they aren’t going to pretend he’s alive but nobody is allowed to see him?

I guess I’ll burn the last 200g on this roll going through the whole calibration suite again while the last one is drying

it has modeled supports that were removed

I’ll try it out. Nextcloud can’t be any less than way more than I want from it, and the lighter options have been not quite what I want either

So you mean all this time when they stop working I’ve been exploding them but I could have been taking them to recycling and they actually get recycled?

I haven’t tried it yet but I ordered a couple of tz v6 v3 for my dual extruder build that has been pending electronics for ages. If they perform well I might get more and put a tool changer on my main printer.

I sort of did this today. I was testing what each setting in orca slicer’s scarf seam section did and I had the scarf flow at 0.6 and forgot I even had scarf seam on but some seemingly random features ended up as disconnected lines and I blew through like half a roll in calibration prints that came out flawless or near flawless before I realized

I’m shocked at how much it recovered. I’m also glad I’m not the only one still running an ender 3.

Do you have a multi meter? You might have to adjust the little screw for the y motor. I’ll see if I can find the instructions for that. The wires in my pic are from the uart mod so I can do it in software.

Edit: people called it vref adjustment. You want it low enough that the motors don’t overheat but high enough that it can move the bed and the print without skipping. If you have an aftermarket board the procedure might be different and you might be able to do it in settings.

Also if you haven’t already, I would also recommend unscrewing the wires one by one in the green screw terminals and clip off the soldered ends and strip off enough to put the bare wire back in and screw them down to avoid the fire risk. Crimped ferrules would be better but that needs a crimper and the ferrules.

Here’s what can happen with the stock soldered wire ends: And I caught this one as the electronics were off the printer and outside of my old ikea lack enclosure. If you dont notice it it could be really bad.

is this why xda became shit?

I laughed way too much at this

Smoking not our future

Ghost in the torrents

All I remember was the guy hallucinating all the time and how cringe the sand walking technique was.

The mentor hallucinations pissed me off because the guy basically dies as soon as he shows up for real.

The zendaya hallucinations just made me think she was too busy to actially film so they edited in promo shots to fill the time. I also forgot I wasn’t watching spider-man a few times

Something something bautista reprising his role as drax…

That said I will eventually watch it

Anne Eye’m

I did a glance on nyaa and there are several releases already

Damn. I was expecting dmca but fuck this jazz too

I usually blame this on the hardware manufacturers for being secretive gatekeepy fucks that make things only work with shitty drivers

Maybe I’m even weirder than I thought but it didn’t seem too difficult to me, but finger grip strength and side of finger skin toughness and grippiness probably make a big difference. Instead of coming from below the pinky is attached normally and wraps around just below the factory seal ring. Instead of on top, index and middle finger both oppose thumb for more torque. Hold with bottle upright on table with slight downward force if the initial turn is too tight.

The other image after closer inspection I don’t even know what its meant to be. At first I thought is was a syringe but the blood donation clinic nurses single hand triple wield that shit easier than I can syringe feed a parrot that could bite my fingers to the bone. It says screwing motion but I have taken apart and assembled so many things without the proper tools or clamps, behind object towards self screw driving without magnetic bits, etc., and I can’t think of a single situation where I would do that even if I had alien mirror hands.

D3d sigma prototyping abs. I was expecting it to be shit but it had no problems at all. It’s actually my remaining stock from the ender 3v2 era and it still works as expected. It’s still available but it could be totally different now for all I know. Several brands became big names now but d3d seemingly became less known. They also had transparent abs which I previously bought for voron toolhead leds but it was out of stock when I was looking at the available colours the other day.

The only recent comparison I can do is the eryone black abs I bought this month that I swear is just stinky petg. Super glossy vaguely waxy feel, very stringy and oozey.