• Fermion
    link
    fedilink
    arrow-up
    17
    arrow-down
    3
    ·
    edit-2
    8 months ago

    Zipper merging requires matching speed with the lane you are merging into so that drivers can make gradual changes in speed to make an opening for the person merging. That avoids sending a wave of brake slams that results from sudden unexpected lane changes. If you’re passing a bunch of people, you’re probably not doing a zipper merge.

    You’re also much less likely to end up with someone not letting you over if they see you matching speed instead of speeding up to the merge point.

    • Nougat@kbin.social
      link
      fedilink
      arrow-up
      16
      arrow-down
      12
      ·
      8 months ago

      If you’re passing a bunch of people, you are using the open lane to travel. By the time the lane you are in comes to an end, you then modulate your speed to match traffic in the slower lane, and merge. Because cars have brakes.

      • Fermion
        link
        fedilink
        arrow-up
        14
        arrow-down
        4
        ·
        8 months ago

        You need to start matching speed at the start of the signage for the merge. At that point it’s no longer just a lane, it is a lane with restrictions.

        You’re not actually increasing total throughput by speeding ahead, you’re only changing the order. The total throughput is determined by the flow of traffic after the constriction point. That flow is smoothest when drivers match speed.

        • czech@lemmy.world
          link
          fedilink
          arrow-up
          16
          arrow-down
          8
          ·
          8 months ago

          What you’re missing is that the “closing lane” is often designed to be utilized to prevent traffic from backing up into another traffic control device.

          While you’re “matching speed” with the open lane that’s hardly moving- traffic has now backed up into an intersection and caused gridlock on cross streets for miles behind you.

          So while “total throughput” on YOUR journey has remained the same you may be causing chaos to the roads around you.

          Your best bet is to just assume the traffic engineers who designed the closure know better than you.

          • Fermion
            link
            fedilink
            arrow-up
            8
            arrow-down
            3
            ·
            edit-2
            8 months ago

            youtube.com/watch?v=cX0I8OdK7Tk

            The middle and last scenario both have people merging in at the end, but only the scenario with matching speed has smooth high throughput flow that alleviates congestion.

            The lane hardly moving is usually because of uneven merging at the closure point. If everyone matches speed then both lanes are filled equally. That’s what the traffic engineers say is best.

            There’s a problematic entry ramp that I used to drive every day on my commute. Traffic would back up around it every day in rush hour. When I matched speed and zippered in at the end, the congestion actually started to clear a little as the lane being merged into started moving substantially faster without people cutting in out of turn.

            • czech@lemmy.world
              link
              fedilink
              arrow-up
              6
              arrow-down
              4
              ·
              8 months ago

              This does not address my point at all. I agreed that your suggestion would not necessarily negatively impact the total throughput on your route.

              My point was that your route does not exist in a vacuum and the utility of the open lane may not be obvious without having the same information available as the traffic engineers who designed the closure.

              • Fermion
                link
                fedilink
                arrow-up
                5
                arrow-down
                1
                ·
                8 months ago

                Matching speed does a better job of filling both lanes evenly and reduces the amount of backed up traffic. The slow lane is what backs up to prior intersections. Matching speed is what allows the slow lane to clear up and prevent affecting upstream intersections. You’re point isn’t actually relevant to what I’ve described because the lane is fully utilized in a proper zipper merge with speed matching.

                So I’m not ignoring the purpose of the merge lane, and I’m not advocating early merging. I’m describing the key aspect of zipper merging that the cruise ahead people are missing.